Service
Building Covering Safety Nets installation across South and West India
Covering a building under repair is a temporary works problem rather than a product purchase. The netting has to contain whatever the work generates, stay attached through the wind the site will actually see, and come down cleanly afterwards. Most of the failures we are asked to look at come from the same cause: the sheeting was tied to scaffold that was never designed to take the extra wind load a clad facade attracts. Getting that relationship right is the whole job.

- Photo estimate on WhatsApp
- Written quotation after survey
- Named material grades
- Eight-state coverage

overview
What building covering nets are for
Covering a building under repair is a temporary works problem rather than a product purchase. The netting has to contain whatever the work generates, stay attached through the wind the site will actually see, and come down cleanly afterwards. Most of the failures we are asked to look at come from the same cause: the sheeting was tied to scaffold that was never designed to take the extra wind load a clad facade attracts. Getting that relationship right is the whole job.
Contains falling debris, tools and dust during facade work so the public, vehicles and neighbouring property are protected.

benefits
What you get from it
- Protects everyone below
- Debris and tools are contained on the facade, which is what allows work to continue over an occupied street or car park.
- Keeps dust off neighbours
- Fine sheeting holds most airborne dust and overspray on site, which is usually the difference between complaints and none.
- Lets the building stay in use
- Residents and tenants can remain in occupation during facade work rather than the site being closed off entirely.
- Comes down without damage
- Planned fixing points mean the sheeting is removed cleanly, leaving no scarring on new paint or cladding.

features
How the system is built
- Graded sheeting weight
- Netting is specified by GSM and aperture to match the work, from coarse debris containment to fine overspray control.
- Flame-retardant options
- Where hot works are planned, flame-retardant sheeting is specified rather than standard netting.
- Wind-aware fixing pattern
- Tie spacing is set from the exposed area and expected wind, because sheeting substantially increases load on the scaffold.
- Phased installation and removal
- Sheeting follows the work up and down the elevation, so only the active zone is clad at any time.

applications
Where it is used
- Scaffold debris containment
- The standard use: sheeting tied to a scaffold to contain material during repair or construction.
- Repainting occupied blocks
- Fine mesh that holds overspray and lets residents keep windows usable through most of the programme.
- Demolition and stripping work
- Heavier containment where material is being removed rather than applied, with correspondingly denser fixing.
- Tall structures and chimneys
- Wrapped containment on slender structures, where wind loading dominates the temporary works design.

materials
Materials we specify
| Material | Specification | Why it matters |
|---|---|---|
| HDPE facade sheeting | UV-stabilised HDPE monofilament, 50 to 150 GSM | Weight is chosen for the work: lighter mesh passes more wind and heavier sheeting contains finer material. |
| Flame-retardant netting | FR-treated polyethylene sheeting | Specified wherever welding, cutting or grinding is planned within the clad zone. |
| Ties and edge reinforcement | UV-stable cable ties or lacing cord with reinforced eyelets | Eyelets spread the load into the sheeting; ties are the intended sacrificial element and are replaced as needed. |

installation
How the installation runs
This is survey-led work. A typical job takes 8 to 60 hours on site once the specification is settled.
Temporary works review
We confirm the scaffold or structure can accept the additional wind load that cladding it will create.
Sheeting specification
Mesh weight, aperture and any flame-retardant requirement are fixed against the actual scope of work.
Phased fixing up the elevation
Panels are fitted and tied progressively, following the work rather than cladding the whole building at once.
Tie inspection regime
Ties are checked at agreed intervals through the programme, since they are what fails first in high wind.
Controlled removal
Sheeting is struck in sequence with the scaffold and removed from site rather than being left in place to weather.
- Confirm the scaffold design accounts for clad wind loading
- Agree the working programme and phasing with the site team
- Establish notification arrangements for residents in occupied buildings

safety
Safety and standards
- Wind loading on clad scaffold assessed against IS 875 Part 3 basic wind speed
- Flame-retardant sheeting specified where hot works fall within the clad zone
- Sheeting changes the scaffold's loading
- Cladding a scaffold can multiply the wind load it carries. It cannot be added to an existing scaffold without checking the design.
- Ties are the sacrificial element
- Ties are meant to be inspected and replaced during the programme; a torn panel usually means ties were left unchecked.
- Containment is not a licence to drop things
- Sheeting is one layer of protection. Good housekeeping at height remains the primary control on any site.

maintenance
Keeping it working
We recommend an inspection every 1 months. Most of it is straightforward enough to do yourself.
- Inspect and replace ties
- Ties are checked frequently through the programme; broken ties concentrate load on their neighbours and cascade.
- Repair tears promptly
- A small tear becomes a large one in the next high wind, so panels are patched or replaced as soon as damage appears.
- Clear accumulated debris
- Material collecting in the sheeting adds weight the fixing pattern was not designed for and is cleared out regularly.

quality
Quality checks and warranty
This product carries a 1-year warranty on materials and workmanship, on the basis that the recommended inspection is carried out.
- Sheeting GSM and aperture recorded against the scope of work
- Scaffold wind-load review confirmed before cladding
- Tie spacing verified on each elevation
- Inspection intervals agreed and logged with the site team

pricingFactors
What drives the price
- Elevation area
- Total clad area is the base measure, taken on the elevations actually being covered rather than the whole building.
- Sheeting grade
- Heavier and flame-retardant grades cost significantly more per square metre than standard debris mesh.
- Programme length and phasing
- A long programme with sheeting following the work up and down the building involves repeated visits rather than one installation.
- Height and access
- Fixing at height, and any need to work outside normal hours over a public area, both add to labour.
We do not publish a rate per square foot, because the same area can differ in price by a factor of two depending on grade, spacing and access. Every quotation states these explicitly.
From one photo to a checked fitting

01
Share the opening
Send a clear photo, your city, and whether the priority is children, pets, birds, visibility, or sports use.

02
Measure and check
We confirm dimensions, fixing surfaces, access, and how the space is used day to day.

03
Compare the estimate
Review material grade, spacing, included installation, warranty terms, and the price unit in writing.

04
Install and inspect
Fit the chosen system, check edges and tension, and walk through basic care before handover.
Our work
Building Covering Safety Nets installation gallery
Installation photography from comparable openings — used to judge finish quality before you book a survey.
Service areas
Building Covering Safety Nets across every state we cover
Pick your city for climate-specific notes and local installation guidance — not one metro paragraph reused nationwide.
Browse by subsection
Each link is its own hub page with unique content, then the same state ladder.

Photo → WhatsApp estimate
Send a clear photo of the opening in your city
One wide shot and a close-up of the fixing surface are enough to confirm coverage, suggest the right system, and outline what should appear on a written quotation before you book a survey. Firm totals still follow measurement on site.
- ✓ City / PIN in the message
- ✓ Priority: kids, birds, view, or monkeys
- ✓ Rough width × height if known
- ✓ Floor / society access notes
Questions we are asked most

How often should an installation be checked?
Once a year is right for most installations, and it is largely something you can do yourself: press the cables or net at mid-span to feel for slack, look at the anchor points for rust weeping or hairline cracking, and wash the surfaces down. In coastal and cyclone-exposed locations we recommend an additional check after the wet season.
Will my apartment association need to approve the work?
In most gated communities and housing societies, yes, because anything fixed to an external wall or balcony counts as a facade alteration. We can supply the drawings and material specification you need to submit. It is worth starting that process early, since approval usually takes longer than the installation itself.
Can residents stay in the building during facade work?
In most cases yes, which is usually the main reason for sheeting in the first place. Fine mesh holds dust and overspray on site so windows remain usable for much of the programme, and we phase the sheeting to follow the work up and down the elevation rather than wrapping the whole building at once.
Can you just sheet the scaffold we already have up?
Not without checking its design first. Cladding a scaffold can multiply the wind load it carries, and a scaffold erected without that allowance may not be adequate once sheeted. We review the temporary works before anything goes up, which occasionally means asking for additional ties before we proceed.
My net or cable has gone slack. Is that a problem?
It needs attention but rarely means replacement. Slack in a cable widens the gap under load, which is the thing a barrier exists to prevent, and slack in a net lets it whip and abrade against fixings. Both are usually corrected by re-tensioning at the existing hardware, which is a short visit rather than a new installation.
Why do quotations for the same balcony differ so much?
Almost always because the specifications are different, even when the dimensions are identical. Cable grade, cable spacing, net polymer and the type of anchor used all change the cost substantially and none of them are visible in a photograph. When comparing quotations, check the stated grade and spacing rather than the total alone.
What warranty do you provide?
Warranty depends on the product, and the figure for each one is stated on its service page rather than promised generically here. In every case the warranty covers materials and workmanship on what we installed, and it assumes the yearly inspection is carried out. We will always tell you what is and is not covered before you commit.
Is there a cheaper specification that is still safe?
Sometimes. Moving from 316 to 304 stainless is a genuine saving and perfectly sound at an inland address, and a coarser mesh is fine if you only need to keep birds out. What we will not do is reduce cable spacing tolerance or anchor quality, because those are the two things that decide whether the installation actually holds.
Do you need to visit before giving a price?
For anything structural we do, yes. We can give an indicative range over the phone from your balcony dimensions, but the final price depends on the condition of the wall or slab we are fixing into, the access route for materials, and the exact spacing you need. A survey takes about twenty minutes and means the quotation we give you is the price you pay.
How long does an installation take?
A cloth hanger is usually done in an hour or two. A single balcony safety net takes two to six hours, and an invisible grill on one or two bays takes most of a working day. Larger jobs such as sports enclosures or building covering run to several days because foundations and scaffold have to be dealt with first.
How long should a safety net last?
A properly stabilised net in a moderate climate should give several years of service, and considerably longer where it is shaded. The way to judge it is by feel rather than by date: twine that has become stiff or chalky and snaps instead of stretching has reached the end of its life and should be replaced.
Do you actually cover my area, or only the main city?
We cover the localities listed on our service area pages, and those lists reflect where we genuinely operate rather than everywhere we would like to. If your locality is not listed, call us anyway: we often work just beyond a listed boundary, and we will tell you plainly if a job is outside our reach rather than sending someone unprepared.
Can you publish a rate per square foot?
We deliberately do not, because a single rate would be misleading. The same area costs very different amounts depending on the grade of hardware, the spacing you need, the height you are working at and the condition of the substrate. Our pricing guide sets out every factor that moves the number so you can see how a quotation is built up.
Photo estimate
Book a survey for Building Covering Safety Nets
Share your city and a clear photo of the opening. We reply with the right system options and what a written quote should include.

Explore more
Related pages & topic clusters
Continue this service, compare nearby locations, or open a buyer guide — every cluster is unique to this page.
Free inspection, written quote, WhatsApp or call — pick the next step.
- Free site inspection
Book a twenty-minute survey.
- Get quote
Send opening photos and your city.
- Request callback
We call back with system options.
- Contact team
Talk to a planner before you decide.
Conversion
Ready for a free site inspection?
Send a photo, book a callback, or call the team — we reply with the right system options for your opening.